| T O P I C R E V I E W |
| Selinger78 |
Posted - 10/25/2005 : 08:45:54 AM
Origin Version (6.0):
Operating System: Win2k
I tried to automize my plots using a script file (with lots of help from the forum!).
Somehow there must be a mistake in the code...
The script works only sometimes, even with the same data the graphs are not always displayed when using the script file. Last time after a programm restart e.g. just one (instead of two) graph windows appeared and this one was empty.
So does anybody with some more experience see an obvious mistake:
[main]
getfile *.dat;
open -w %A;};
wks.col1.Width=15;
wks.col2.Width=15;
wks.col3.Width=15;
wks.col4.Width=15;
wks.col5.Width=15;
wks.col6.Width=15;
wks.col1.name$="time";
wks.col2.name$="temperature";
wks.col3.name$="eline";
wks.col4.name$="ellipse";
wks.col5.name$="transmitted";
wks.col6.name$="outerring";
col(transmitted)=col(transmitted)*10^1,4;
col(transmitted)=col(transmitted)*10^(-4);
wks.col3.label$="e-line";
wks.col5.label$="transmitted beam";
wks.col6.label$="anisotropic ring";
wks.col4.label$="ellipse";
worksheet -s 1;
worksheet -s 3;
worksheet -s 4;
worksheet -s 5;
worksheet -s 6;
//windowname=%H;
win -t P "00_langzeitmessung-4-dioden über der zeit.OTP" %H _E_full range;
//lay -i %W_time;
lay -i %W_eline;
lay -i %W_ellipse;
lay -i %W_transmitted;
lay -i %W_outerring;
set %W_eline -c 2;
set %W_ellipse -c 3;
set %W_transmitted -c 4;
set %W_outerring -c 5;
//Rescale;
win -t P "00_langzeitmessung-4-dioden über der zeit - bis 100s.OTP" %w _E_up_to_100_s;
//lay -i %W_time;
lay -i %W_eline;
lay -i %W_ellipse;
lay -i %W_transmitted;
lay -i %W_outerring;
set %W_eline -c 2;
set %W_ellipse -c 3;
set %W_transmitted -c 4;
set %W_outerring -c 5;
//layer.x.rescale=1; // manual
//layer.y.rescale=2; // normal
//Rescale;
|
| 3 L A T E S T R E P L I E S (Newest First) |
| Selinger78 |
Posted - 10/26/2005 : 05:25:13 AM
As always you were right.
Don't know how the bracket came there. With your first 3 lines it works fine. I also changed the template-names just to be sure to produce no more errors or strange outputs.
Thank you!
Selinger78
|
| Mike Buess |
Posted - 10/25/2005 : 11:11:33 AM
1. The unnecessary "};" at the end of the open command is sure to produce wierd results. (Assuming it's not just a transcription error.) Also, I don't see where you've defined %W. First three lines should be
getfile *.dat;
open -w %A;
%W=%H;
2. The '?' character is not allowed in file names. (your graph template) That could also be creating problems.
3. Your worksheet -s commands merely select the columns one at a time ending up with only col 6 selected. Does no harm but serves no purpose since you add the columns one at a time to each graph layer.
Mike Buess
Origin WebRing Member |
| Selinger78 |
Posted - 10/25/2005 : 09:00:22 AM
I just noticed the following:
When I start the script in a new Project an empty graph with just axis appears. When I delete this window an open the first template from the script manually then I get the dat displayed but all in red color.
When I then delete this graph window again and rerun the script then everything is correct - both graphs are displayed with right colors and legends.
has anybody an idea how the manage this?
Regards,
Selinger78
|
